how to change batteries in honeywell thermostat

Quick Installation Guide Install Batteries Pull out the battery cover. There isnt any reset button or anything to reboot the thermostathere is what I would try.

Honeywell Thermostat Programming Rth2310b Youtube

Before resetting the thermostat make yourself familiar with the houses wiring.

How to change battery in honeywell thermostat rth2310b. I installed a Honeywell rth230b thermostat. Generally you can change the batteries of the Honeywell thermostat by just pulling out the cover plate or just sliding out the battery compartment. Turn the system off and then remove the batteries.

The first and foremost thing that you will need to check is the compatibility of your battery with the thermostat. You will hear a clicking sound. Replace batteries once a year or before leaving home for more than a month.

Install two fresh AA batteries when the low-battery icon flashes on the screen. Wait 10 seconds and then reinstall the batteries. Press P to go to the next period.

Make sure the thermostat switch has been set to Off Push the battery door open by inserting a coin or a similar alternative into the slot found on the door. Afterwards the screen displays the actual tempera- ture. Once the batteries are replaced.

Press Exit to exit. Watch this video and you will kno. This thermostat is ready to go.

1 Set the clock see page 7 2 Select whether to heat or cool see page 8 3 Select whether to keep the fan on continuously or only when needed see page 9 This thermostat is pre-set with energy-saving program settings see page 11. You are all set. Otherwise the heatingcooling system might remain activated even when batteries are removed.

It is not exactly easy but it is possible. Repeat steps 2 to 8 for each of the remaining periods. The other settings are not erased when the thermostat is without power.

Install fresh batteries when the replace battery warning begins flashing. I installed the batteries but the display clock just blinks and you cannot adjust the temperature. Will cut power to the heatingcooling unit.

Removing the thermostat from the wall is not required. You were in Heating mode switch to Cooling mode. Wait 10 seconds and then reinstall the batteries.

The 4000 series of Honeywell Thermostat are a line voltage control with a voltage range of 120240 Volts. Install the batteries as shown. An icon appears when the batteries need replacement.

The set-point for that mode flashes. After replacing the batteries readjust the time and day see section. This icon will flash for 120 days then the thermostat.

There are far too many models out there and you need the right battery to be connected with these thermostats or it will not work with the thermostat. This video will show you how to replace the batteries in a Honeywell thermostat. The battery housing is not labeled but it is easy to locate it.

The following steps are helpful to change the battery in Honeywell thermostats. Before this you could attempt to see if the battery door will open by pressing it. Replace the battery and put it as it was earlier.

When the thermostat comes back online press and hold the mode button until you see the date and time. How To Change Battery In Honeywell Thermostat Rth2310b. Once the thermostat is reset you would need to re-adjust the clock and other settings.

Haziran 07 2021 Yorum Gnder. The icon disappears once the batteries are replaced. Simply perform the three steps below and the thermostat is in operation.

Honeywell RTH2310B Owners Manual About your new thermostat Your new Honeywell thermostat has been designed to give you many years of reliable service and. Honeywell Thermostat Battery Replacement Not Working. After the batteries are installed the thermostat per- forms a series of tests for approximately 5 seconds.

To program a period you need to set its start time and its two temperature settings one when the thermostat is in cooling mode and another one when it is in heating mode. How to program honeywell thermostat rth2310b. Reinstall the battery cover.

About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy Safety How YouTube works Test new features Press Copyright Contact us Creators. If the thermostat is not working properly or indicates a low battery then its time for a battery change. I changed the batteries three times with the same results.

To use the schedule place the thermostat in programmable mode. Battery Replacement RTH2310 Programmable Thermostat Battery replacement Set the System switch to Off before removing the batteries. Here is how to perform a Honeywell thermostat reset.

After replacing the batteries set the time and the day see page 7. Try waiting a minute or two then reinstall the batteries and turn it back on. 1 Set the clock see page 7 2 Select whether to heat or cool see page 8 3 Select whether to keep the fan on continuously or only when needed see page 9 This thermostat is pre-set.

Set the desired temperature using the buttons. Simply perform the three steps below and the thermostat is in operation. That may be enough to clear whatever the glitch is.

Honeywell Thermostat Battery Replacement How To Change Batteries Youtube